for SKU.EP-KT200F-J+EP-KT200DG: 2023 ECUHELP KT200 ECU Programmer Offline Workstation for Car Truck Motorbike Tractor Boat in Suitcase [Get a Free KTflash Dongle]
ECUHELP KT200 Offline Workstation Read/Write 5000+ECU, 500+TCU Gearbox of Car Truck Tractor Boat Motorbike on Bench, OBD, Full System, BDM/JTAG, TOOL BOOT Mode. Compatible with any computer. No registration & activation. EU/ USA delivery. Free update, no annual fee.
1 votes
Q:Question:Can KT200 read ECUs on the bench without the need to open them? Answer this question
Q:Question:Dose anybody have any success cloning EDC17CP18 with TC1796 MCU using the KT200 with the latest software? This ECU is found on 2009-2014 GM Duramax diesel vehicles (Express & Savana vans, Silverado 25 Answer this question
A:Answer:
Direct cloning is not possible with KT200. However, it does support partial cloning, specifically for immobilizer data, and also allows for immobilizer off functionality.
Q:Question:Can ECUHELP KT200 ECU Programmer change the VIN number? Answer this question
A:Answer:
While we do not endorse this use by our customers, the ECUHELP KT200 ECU Programmer does offer support for VIN number changes. However, it is important to note that altering the VIN number may have legal implications, and it should be done in compliance with applicable laws and regulations.
Q:Question:Which types of vehicles are compatible with the KT200 ECU Programmer? Answer this question
A:Answer:
ECUHELP KT200 ECU Programmer supports a wide range of vehicles, including cars, trucks, motorcycles, tractors, and boats. It covers up to 5400 ECUs and over 500 TCUs. For a comprehensive list of supported vehicles, please refer to our vehicle list. KT200 ECU list: https://www.ecuhelpshop.com/uploads/item/168138595688098313.pdf KT200 TCU list: https://www.ecuhelpshop.com/uploads/item/168138726200601103.pdf.
Q:Question:With Ecuhelp kt200 01/02/2023? the software don’t works in win7 x64? Answer this question
A:Answer:
KT200 is compatible with bioth windows 7 and windows 10, but advise you install in win10/11 instead of win7. Here is the in-depth guide: https://www.ecuhelpshop.com/product-technical/how-to-use-ecuhelp-kt200-to-r-w-ecu-tcu.html.
Q:Question:Can I RW DCM6.2A in Peugeot expert with KT200 ecu tool? Answer this question
A:Answer:
Yes via obd work fine. There are two videos to show kt200 DCM6.2A test reports and procedures. https://youtu.be/Q8CzbrTv_QA https://youtu.be/IFAEe6icR_0
Q:Question:Is it possible to program an R8 V10 5.2L MED9.1 (Master and Slave ECU) OBD/Bench mode? Answer this question
A:Answer:
It is extremely important to do this through BDM. You need to read a 2.5 MB file and save the EEPROM. If you don't, you will get a "check vehicle" message on the dashboard. Do not attempt this with any tools via OBD.
By Der Käufer
on May 31, 2024
First, perform a full backup on the bench/boot for both ECUs.
By Kristina
on May 31, 2024
Yes, you can use the tool, but you need to bench and backup both the MPC and EEPROM. If you crash one ECU, you will need to replace both ECUs and visit a VW dealer.
Q:Question:I can't start KT200, when start any kind of reading i got message "wait for internet connection" and crashed. AV and firewall not exist at computer... any solution? Answer this question
A:Answer:
ftp installation is missed ! After installation, it works.
By Sunny SmithSELLER
on November 1, 2023
0 votes
Q:Question:I purchased a KT200 today, and I have a few concerns. I've heard from a friend who used it in the past that the KT200 ecu breaks down and bricks it. Is there a risk of damaging the ECU while using th Answer this question
A:Answer:
Indeed, any tool or even unintentional actions, like static electricity from one's fingers, can damage an ECU. It's always best to handle with care and gather ample knowledge before proceeding.
By Jerry
on October 24, 2023
There's always a potential risk of bricking any ECU, regardless of the device, even with genuine programmers. This is why I advise newcomers to be cautious. Avoid start like crazy and test on customer car that need daily.
Q:Question:I've just received my KT200. Where can I download the required software? Also, should I use the original power adapter provided in the box, or use another power adapter? I've heard Some people say you Answer this question
A:Answer:
For the KT200 software, you can download it directly from: https://www.ecuhelpshop.com/pages/downloads/. Regarding the power adapter, the original one provided should enough for most ECUs. However, if you encounter ECUs that demand higher voltages, like 13.5-14v, you'll need to use a different power source.
By Sunny SmithSELLER
on October 24, 2023
0 votes
Q:Question:I have a problem with my KT200 offline, when I try to connect to the ECU the software turns off.If I work online, they don't turn off. Any solution? Answer this question
A:Answer:
Install ftp in installed kt200 offline and will not close.
![2023 ECUHELP KT200 ECU Programmer Offline Workstation for Car Truck Motorbike Tractor Boat in Suitcase [Get a Free KTflash Dongle]](/uploads/item-x300/171567699956007574.webp)
![[EU Ship] ECUHELP KT200 II ECU Programmer Full Version with Offline Dongle for Car Truck Motorbike Tractor Boat,R/W ECU Bench/OBD/BOOT/BDM /Jtag Mode](/uploads/item-x300/171136130037011118.webp)
![[Suitcase] ECUHELP KT200 ECU Programmer, Read Write Car Truck via OBD / on Bench / in Boot Jtag [Get Free KTflash]](/uploads/item-x300/171567677819843923.webp)